Intelligent inverter with charger

6kw-48V inverter built in charger and battery

Soure:2016-1-7 update:2016-1-7 hits: font-size:B M S
 Inverter Technical:

1, Two kinds of start mode: Reduction Voltage Start and Variable Frequency Start. Customers can set start mode according to the nature of their load.

2, The output frequency can be set, this function is very convenient for customer.

3, The output voltage can be set between +20 % to -40 % of rated voltage. It’s a great convenience to users.

4, The DC input voltage range can also be set. Over-voltage point, under-voltage point, over-voltage recovery point, under-voltage recovery point all can be set via the LCD panel. Convenient for increasing or reducing the quantity of batteries, photovoltaic modules also can be used flexibly.

5, Pure sine wave output. with good transient response less than 40MS, little harmonic distortion, higher conversion efficiency and stable output voltage.

6, Powerful data display and fault instruction function. LCD can display the DC input voltage, output frequency, phase voltage, phase current, AC bypass input voltage, output power KWH, time and date, temperature, fault code display.

7, Using the fifth generation efficient IPM intelligent module from Japanese Mitsubishi, high efficiency and stable performance. It with powerful protection function, the protection for short circuit, over load, over temperature is more safe and reliable. It’s service life can up to 15 years or more.

8, Wide input voltage can be set according to customer’s requirement. Input voltage range can be selected from 100-500V or 200-850V.

9, Product have passed the European CE (EMC and LVD) certificated and accredited by Australia CEC energy network.

Controller Technical:

◆Adopt PWM multistep sequential limiting current charge method, auto control multiple solar array connection or shut off orderly according to the battery group voltage change tendency.

◆Adopt multiple-circuit charging-control circuit and individual killer switch on each circuit.

◆With auto protection function of over charge, electronic short circuit, anti-reverse protection. Prevent the battery group reverse charging to the solar panel array at night.

◆Big intuitionistic LCD screen shows the working status of solar panels, battery and controller. ( the voltage, current, power of solar energy panel and battery)

◆Power switch driving circuit is completely isolated from sampling circuit. The control signals is transmitted by opto isolation, with super-high disturbence rejection and stability.

◆Power switch driving circuit is completely isolated from sampling circuit. The control signals is transmitted by opto isolation, with super-high disturbence rejection and stability.

◆There are lightning protection device inside the controller. Limit instantaneous overvoltage which entered into solar panels under a level which the system can withstand; or unload the strong lightning current to the ground. To protect the equipment from lightning surge.

◆Adopts the industrial-grade chips for all control, which can work under the cold, hot, humid conditions.

◆Temperature compensation function. Compensate the temperature according different battery type.

◆Fixable communication solution with RS-232,RS-485,USB,GPRS,Etherner,etc.

Model

BZP-6KW

Isolation mode

Low Frequency Transformer

DC Input

Rated voltage (Vdc)

48V

Rated current(A)

125A

Rated Charge current(A)

50A

Battery(V)

4*12V-100AH

AC Output

Rated output power

6KW

Output waveform

Pure Sine Wave

Rated Voltage

220V±3%

380VAC±3%

Phases

Single phase

3 phase 4 wire

Rated current(A)

27A

9A (phase current)

Frequency

50Hz or 60Hz

Rated output voltage range (V)

110/120/220/230/240/380/400/415VAC optional

Power Factor(PF)

0.9

Overload Ability

150%, 5 seconds

Efficiency

>93%

Waveform distortion rate (THD)

<3%(linear load="" p="">

Dynamic Response (0 to 100% load)

5%,≤50ms

Display

LCD

Running mode

Working continuously

Electrical insulation properties

2000Vac, 1 Minute

Protection Function

Protection

Input reverse polarity, under voltage, overvoltage, output over-current, short circuit, overheating etc.

Cooling method

Fan-cooled

Short-circuit protection

No automatic recovery, need to restart the machine

Working environment

Noise ( 1 meter)

≤50dB

Degree of protection

IP20(indoor)

Working Altitude(m)

≤2000

Working temperature

-25~+55℃

relative humidity

0~90%,non-condensing

Mechanical dimension

Depth* Width * Height

540x540x760mm

Weight (Kg)

180Kg

 


Copyright © Yueqing BangZhao Electric Co., Ltd. 2013
address:Shangyou Industrial Zone Liushi Town Yueqing City, Zhejiang Province Chinese TEL:86-577-61771566 FAX:86-577-27873806